Installation Guide

Set up your BarnTalk Alarm System in a few steps

Place order

How to pair sensors with gateway?

1. Open the sensor

1. Open the sensor

Open the Sensor by unscrewing the cap on the sensor
2. Switch ON the sensor

2. Switch ON the sensor

Pull the circuit board out a bit and then slide the power switch on the circuit board to “ON” (slide left switch to the right)
3. Pair sensor with  gateway

3. Pair sensor with gateway

  1. Press and hold the red button ("pairing") in the gateway and the pairing button in the sensor at the same time as shown in the image above.
  2. Hold both the buttons for 10 seconds or until you see a flash of red light on either the gateway or the sensor.
  3. Once the red light flashes you can stop from holding them. Now your sensor is paired to the gateway!
4. Place the sensor in the barn

4. Place the sensor in the barn

4.1 Use "a zip tie” provided with the package or metal hanger and attach to the sensors as shown in the image.

 4.2 Place the sensors in the barn.

How to restart sensors?

1. Open the sensor

1. Open the sensor

Open the Sensor by unscrewing the cap on the sensor
2. Switch ON the sensor

2. Switch ON the sensor

Pull the circuit board out a bit and then slide the power switch on the circuit board to “ON” (slide left switch to the right)

What to do if the gateway does not show up on the app?

1. Open the sensor

1. Open the sensor

Open the Sensor by unscrewing the cap on the sensor
2. Switch ON the sensor

2. Switch ON the sensor

Pull the circuit board out a bit and then slide the power switch on the circuit board to “ON” (slide left switch to the right)

What if the gateway is offline in app after it is added?

1. Open the sensor

1. Open the sensor

Open the Sensor by unscrewing the cap on the sensor
2. Switch ON the sensor

2. Switch ON the sensor

Pull the circuit board out a bit and then slide the power switch on the circuit board to “ON” (slide left switch to the right)

What if the sensor is offline in app after it is added?

1. Open the sensor

1. Open the sensor

Open the Sensor by unscrewing the cap on the sensor
2. Switch ON the sensor

2. Switch ON the sensor

Pull the circuit board out a bit and then slide the power switch on the circuit board to “ON” (slide left switch to the right)

How to pair sensors with gateway?

1. Open the sensor

1. Open the sensor

Open the Sensor by unscrewing the cap on the sensor
2. Switch ON the sensor

2. Switch ON the sensor

Pull the circuit board out a bit and then slide the power switch on the circuit board to “ON” (slide left switch to the right)

How to restart gateway?

1. Open the sensor

1. Open the sensor

Open the Sensor by unscrewing the cap on the sensor
3. Pair sensor with  gateway

3. Pair sensor with gateway

  1. Press and hold the red button ("pairing") in the gateway and the pairing button in the sensor at the same time as shown in the image above.
  2. Hold both the buttons for 10 seconds or until you see a flash of red light on either the gateway or the sensor.
  3. Once the red light flashes you can stop from holding them. Now your sensor is paired to the gateway!

How to see if the sensor is working with gateways?

1. Open the sensor

1. Open the sensor

Open the Sensor by unscrewing the cap on the sensor
2. Switch ON the sensor

2. Switch ON the sensor

Pull the circuit board out a bit and then slide the power switch on the circuit board to “ON” (slide left switch to the right)
3. Pair sensor with  gateway

3. Pair sensor with gateway

  1. Press and hold the red button ("pairing") in the gateway and the pairing button in the sensor at the same time as shown in the image above.
  2. Hold both the buttons for 10 seconds or until you see a flash of red light on either the gateway or the sensor.
  3. Once the red light flashes you can stop from holding them. Now your sensor is paired to the gateway!

How to pair sensor and a gateway?

3. Pair sensor with  gateway

3. Pair sensor with gateway

  1. Press and hold the red button ("pairing") in the gateway and the pairing button in the sensor at the same time as shown in the image above.
  2. Hold both the buttons for 10 seconds or until you see a flash of red light on either the gateway or the sensor.
  3. Once the red light flashes you can stop from holding them. Now your sensor is paired to the gateway!

How to setup mobile app?

1. Open the sensor

1. Open the sensor

Open the Sensor by unscrewing the cap on the sensor
4. Place the sensor in the barn

4. Place the sensor in the barn

4.1 Use "a zip tie” provided with the package or metal hanger and attach to the sensors as shown in the image.

 4.2 Place the sensors in the barn.

How to install mobile app?

1. Open the sensor

1. Open the sensor

Open the Sensor by unscrewing the cap on the sensor
© 2020 BarnTools. All Rights Reserved.